WST100
WST100 ESD Gear Tester
The simple Test Station for ESD wrist straps and ESD shoes.
For the reliable test of effectiveness of ESD precautionary measures like wrist straps and conductive footwear. The WST-100 ESD Tester is handy and portable and offers a reliable yet cost efficient solution before accessing ESD-secured areas.Application
Specialities
+49 7628 35 94 064
We gladly help you to solve your problem.
WST100 Specification
- Easy measurement by pressing the metal contact plate
- Simple display with 7 LEDs: green for “OK” and red LED error message for wrist strap, left shoe and right shoe each for lower and upper limit
- Calibrated to resistors: wrist strap lower: 750kΩ, upper: 35MΩ; shoe test lower: 100kΩ, upper: 35MΩ
- Built-in buzzer for acoustic signalling
- Robust plastic case
- Only 155 x 88 x 35 mm, shoe tester 440 x 370 x 35 mm
- Relais w./ output for door control (potential free contact 60V/0,5A)
- Powered by 4 AA batteries
- Shipped with hand device, shoe electrode, batteries, manual and calibration certificate
Robust and reliable
For mobile or stationary use
Very simple operation
With entrance control/door opening function
Rechargeable Batteries Set
Charging set with 4 NiMH accumulators and plug charger/power supply
PC Connection Set
Interface cable and Software to read out the static memory to a PC
All products within this product category:
EFM113B
EFM113B Precise Field Strength Sensor
The easily installable Sensor for accurate measurement of surface charge.
EFM113B: installation distance typically 150mm but can be varied For the stationary automatic measurement of field strength i.e. amount of static charge of material surfaces. The Sensor EFM113B measuring field strength, is a very small but very accurate field strength sensor which supplies the results as analog signals and thus can be used to record or control ionisers or processes in the production flow. Especially suited to control the E5000 Anti-Static Bar. For visualisation and recording also easily connectable to ISM500 Data Monitor.Application
Specialities
+49 7628 35 94 064
We gladly help you to solve your problem.
EFM113B Specification
- Measurement distance typically 150 mm
- 4 measurment ranges up to 200 kV
- Output: +/- 1mA
- Power supply: 9-15 V DC
- Gold-plated stainless steel sensor, calibration with 200×200 mm plates
- Potentiometer to adjust zero balance
- Only 120 x Ø 36 mm in dimension
Low maintenance
Robust, industry-proof design
Easy mounting
Very precise
Very compact
Homogenising Plate
Homogenising plate for even more accurate measurement for high charges and large areas
Signal Converter
Converts EFM113B electrical output to 4-20mA/0-10V signals for easy connection to a process controller.
All products within this product category:
VOLTSTICK
VOLTSTICK Simple Bar Checker
A pen-shaped sensory device to detect alternating voltage fields.
For the very quick and simple detection of the working of an AC neutralising ionizer (also to some degree for DC bars). The Voltstick allows the contact-free easy detection, if an AC neutralising ioniser builds-up an alternating field (and in turn ionising charge) and thus if it is working or not. The Voltstick is also available in an ATEX-certified version with EX II 2 G Ex ib IIC T4 classification.Application
Specialities
+49 7628 35 94 064
We gladly help you to solve your problem.
VOLTSTICK Specification
- Contact-free detection of alternating currency (AC)
- Measuring range 90 – 1000 V at 50/60 Hz
- Green LED indicates readiness
- Upon detection of alternating currency a red LED starts to pulse and an acoustic signal occurs*
- If the reading point is free of charge the tip of the device will constantly illuminate in green and an audible signal starts
- On/Off-switch for torch light
- All external surfaces of the device are of highly insulating material
- Robust doubled casing
- Pen-shaped with pocket clip
- Weight 50g
- Security standard: EN 61010-1; CAT III 1000 V
- Powered by 2 x 1,5 V battery AAA (UM-4)
* ATEX Version: no lamp and no soft button to press, the device is permanently on and operating and ist head is red illuminated when alternating current is detected, there is no acoustic signal
Pocket-size
Simple operation
Quick check whether high voltage is present or not
Robust
no specific accessories
All products within this product category:
F720
F720 Static Bar Checker
A small and simple device to control the operation of an anti-static AC bar.
To check for proper operation of the neutralisation function of an AC static elimination bar. The Static Bar Checker F720 works by measuring the electric charge induced onto the internal sensors by the emitter pins of an AC Static Eliminator Ioniser. Thus, an inference on the functionality and required maintenance (e.g. advancing contamination) can be made, yet the device is absolutely easy and safe in operation.Application
Specialities
+49 7628 35 94 064
We gladly help you to solve your problem.
F720 Specification
- Test distance several mm or touching the emitter tips directly
- One-button operation
- Only 99 x 65 x 24 mm in dimension
- 5-step LED-display of electric charge or discharge performance respectively of an AC Ioniser
- Power consumption 16mA
- Operation with a 9V PP3 battery
- Life-cycle of one battery: 34h continuous operation or app. 10’000 single measurements
Pocket-size
Simple operation
Allows to quickly detect malfunction and maintenance need
Robust
no specific accessories
All products within this product category:
F740
F740 Surface Resistance Checker
A comfortable portable device to determine the resistance of surfaces.
For the measurement of the resistivity of material surfaces as indication for chargeability and conductivity e.g. when changing material or for non-specifiable material. The SRM F740 allows through the measurement of the surface resistivity to infer the affinity of a material’s surface for electrostatic charge or the possibility for deliberate charging for adhesive matters. Addionally, the conductivity measurement (resistance to ground) allows to determine, if through earthing measures alone, electrostatic charge can be discharged.Application
Specialities
+49 7628 35 94 064
We gladly help you to solve your problem.
F740 Specification
- Easy testing by simply placing on surface to be tested
- Automatic adaptation of metering range
- Measurement cf. ASTM Standard D257 parallel bar sensing
- One-button operation
- Only 130 x 70 x 25 mm dimensions
- 15-step LED-display of resisitivity and resistance within defined range separated to “Conductive”, “Static dissipative” and “Insulative” surfaces
- Powered by 9V PP3 battery
- Shipped with protective sheath, battery and cable
Pocket-size
Simple to operate: place device on surface, push button and read result
Allows to detect electro-static affinity
Robust
no specific accessories
All products within this product category:
EX715
EX715 Static Meter ATEX
The only Electric Field Meter for daily use in hazardous areas (ATEX).
To manually measure the field strength i.e. amount of static charge and polarity of material surfaces. The Static Meter for Hazardous Areas EX715 is the only device in the market and on top of that a handy and safe device to measure the field strength of up tp 200 kV at the location in hazardous areas 1 and 2. Certified for EX II 2 G Ex ia IIB T4/T5Application
Specialities
+49 7628 35 94 064
We gladly help you to solve your problem.
EX715 Specification
- Test distance 100mm
- 2 measurement ranges up to 200 kV with autom. adaptation
- Hold button
- Stainless steel sensor, calibration with 150×150 mm plates
- Anodised aluminium case
- Only 124 x 64 x 24 mm in dimensions
- LCD panel displaying charge and polarity
- Powered by 9V PP3 batteries
- Automatic switch-off
- Certified for EX II 2 G Ex ia IIB T4/T5
- Baseefa 07ATEX0159
- Shipped with carrying case, battery, ground cable, manual and calibration certificate
ATEX certified
Pocket-size
Simple operation
Due to HOLD function also easy to measure in difficult places
Robust
no specific accessories
All products within this product category:
EFM715
EFM715 Static Meter
The simple and robust Electric Field Meter for daily industrial use.
To manually measure the field strength i.e. amount of static charge and polarity of material surfaces. The Static Meter EFM715 is a handy portable device to measure field strength of up to 200 kV directly at the location.Application
Specialities
+49 7628 35 94 064
We gladly help you to solve your problem.
EFM715 Specification
- Test distance 100mm
- 2 measurement ranges up to 200 kV with autom. adaptation
- Hold button
- Stainless steel sensor, calibration with 150×150 mm plates
- Anodised aluminium case
- Only 124 x 64 x 24 mm in dimensions
- LCD panel displaying charge and polarity
- Powered by 9V PP3 batteries
- Automatic switch-off
- Shipped with carrying case, battery, ground cable, manual and calibration certificate)
Pocket-size
Simple operation
Due to HOLD function also easy to measure in difficult places
Robust
no specific accessories
All products within this product category:
EFM022
EFM022 Comfortable Static Meter
The accurate and very comfortable handheld Field Meter for daily use.
To manually measure the field strength i.e. amount of static charge and polarity of material surfaces. The Static Meter EFM022 is a handy one-button test device with very accurate measurement of field strength of up to 200 kV and not requiring a manual calibration/zero balance. The optional set EFM022- CPM is additionally able to determine the neutralisation performance (over time) of ionising bars.Application
Specialities
+49 7628 35 94 064
We gladly help you to solve your problem.
EFM022 Specification
- One-button operation with Hold functionality
- 5 measurement distances and range up to 200 kV measurement range
- Antistatic EPA casing
- Only 122 x 70 x 26 mm in dimension
- LCD-panel with 2-row display of selected distance and measured electrostatic charge
- Powered by 9V PP3 battery
- Shipped with protective sheath, battery, ground cable, distance holder, manual and calibration certificate
Pocket-size
Very simple operation: 1-handed operation possible
Measuring distance can be set manually if required
Due to HOLD function also easy to measure in difficult places
Robust
Option Charge Plate Monitor
EFM022-CPM to test the performance of neutralising ionisers
With the Charge Plate Set 022 the EFM 022 turns into a Charge – Plate – Monitor (parallel-plate capacitor) to test ionising devices cf. standards EN 100015 bzw. EOS/ESD S.3.1. To this end, an insulated plate, mounted atop the EFM022 is charged up with highvoltage and placed with switched on meter brought in the operating range of the neutralising ioniser. Later should neutralise the charge now, which can be measured over time with the EFM022.
The charging electrode corresponds with its capacity of 20pF to the standards. The neutralisation time from + 1.000V to + 100V or – 1.000V to -100V is measured with a Start/stop Timer integrated into the EFM 022. Charging the capacitor plates is done with a HV converter, part of the whole set and powered via 9V rechargeable battery (incl. battery recharger).
The set contains:
- Carrying case with anti-static rubber foam inlays
- 3 pcs. 9V NiMH – rechargeable batteries
- Battery recharger for 9V r. batteries
- CPS device socket
- Plate Capacitor
- HV converter
- Ground cable 1,5m and 1m
- Crocodile clip
- Operating manual
Charge Plate Monitor
for the periodic manual test of the performance of anti-static ioniser according to standards EN 100015 or EOS/ESD S.3.1 respectively, refer to tab “OPTIONS”
All products within this product category:
ISM500
ISM500 Static Monitor Data Recorder
The compact field monitor processes sensor and bar signals at the machine.
For the visualisation and recording of the measured charge signals supplied by the Field Sensor EFM113B and/or Ionising Bar E5000 during the operation. The Static Monitor Data Recorder ISM500 is a robust device to display and record the data at the location, on SD-memory cards allowing also the analysis and/or archiving later. The «scope of delivery» also consists of the complete configuration of the device in our factory according to the customer specification, so the customer finally gets a plug-and-play solution.Application
Specialities
+49 7628 35 94 064
We gladly help you to solve your problem.
ISM500 Specification
- 5,7 inch colour TFT display
- Standard: 1 galvanically insulated analog input (optionally up to 4)
- Diverse display-options: e.g. curves or data
- Relay output, configurable
- Recording/saving data on SD cards (e.g. for analysis in Excel etc.)
- 6 soft-buttons for menu and operation
- Robust plastic case
- Dimensions 144 x 144 mm
- Universal mounting options
Small and robust
Easy to operate and bright display
Flexible mounting options
Manifold configuration options
Data recording over long periods also on SD cards
Retrofittable interface card with 1 additional channel for further sensors or electrode signalsAdditional I/O Channel
Network Interface
Retrofittable interface card TCP/IP Ethernet for communication via a LAN
Upgradeable interface card with additional relay outputs for alarms etc.Additional Doppel-Relais-Kit
Connection Cable
Cables in diverse length to connect antistatic bars, sensors etc.
All products within this product category:
Measurement/Control Systems
Handheld Meters
Measuring devices for electrostatic application requirements for occasional manual measurements of electrical fields, surface resistances or determination of the electrode function.
Stationary Sensors
Measuring devices for stationary use to determine electrostatics or efficiency of protective measures.
Data Processing
Data recorder and converter to process signals from electrodes, power supplies or sensors locally.